Journal of the Japan Society of Polymer Processing
CONTENTS NOVEMBER Vol.5 No.11 1993

Special Issue on Injection Molding

Preface: Zenichiro Maekawa, 711

Technical Reports
Cavity Local-pressurizing/vibrating System "Press α": Yasushi Utaka / Nobuhiro Ogura / Hideki Yoshida, 712
Injection Machine Control and Quality Control: Michiaki Takizawa / Takashi Magario / Kazuo Usui, 719
Application and Development of CAE in Injection Molding: Ryo Nakano / Satoshi Sawada / Junichi Matsumura, 726
Application to Injection Molding Dies by CAE: Kuniaki Konishi / Yoshimasa Sanpei / Tsuguo Kobayashi, 731
An Example of Warpage Analysis on a Rear Console Used in an Automobile: Minoru Yoshida / Toshiaki Hieda / Kazumi Munemasa, 737
Fiber Orientation Analysis of Grass-fiber-reinforced Nylon: Yasuhiro Kiten / Kazuto Abe / Akinori Kodama / Makoto Inaba, 741

Original Papers
Estimation of Birefringence Due to Stress and Molecular Orientation Induced in an Injection-molded Polymer Strip: Yasuo Kurosaki / Isao Satoh / Hirofumi Uchida, 747
Temperature Measurement in Heating Cylinder of an Injection Molding Machine - Temperature History and Distribution during Molding Process -: Teruo Kimura / Masanori Takeuchi / Akira Hashimoto / Keiji Tsuda / Shinji Murakami / Susumu Hayasaki, 757
A Study on a Practical Simulation Method for Flow Analysis of Polymer Melts in Dies Part I An Examination of an Analysis Method that Reduced Memory Capacity and CPU Time: Kazutaka Sakaki / Yoshifumi Kuwano / Toshihisa Kajiwara / Kazumori Funatsu, 764
Temperature Measurement of a Molten Resin in an Injection Molding Machine by Using an Ultrasonic Technique: Nobuhiko Nishiwaki / Masaaki Konno / Ailing Cui / Sankei Hori, 772
Pressure Measurement in Molding Process by Ultrasonic Wave: Nobuhiko Nishiwaki / Masaaki Konno / Ailing Cui / Sankei Hori, 779
A New Ultrasonic Method of Measuring the Crystallinity of Molded Thermoplastics: Nobuhiko Nishiwaki / Ailing Cui / Masaaki Konno / Sankei Hori, 786
Generation Mechanism of Residual Stress during Injection Molding Process: Mamoru Ishijima / Masashi Yamabe / Hiroaki Shimoda / Minoru Shimbo / Yasushi Miyano, 792
Influence of the Injected Resin Temperature Behavior through the Nozzle on Moldings: Nobuhiko Nishiwaki / Konno Masaaki / Ailing Cui / Nobuaki Hashimoto / Sankei Hori, 800
Part Buckling in Injection Molding (I): Hiroyuki Kikuchi / Kiyohito Koyama, 806
Processing and Properties of Fiber Reinforced Article with Sandwich Structure in Simultaneous Composite Injection Molding: Kiyotaka Tomari / Susumu Hayasaki / Hiroki Takashima / Ming Xia / Hiroyuki Hamda, 813
Change in Gear Accuracy and Tooth Profile of Injection Molded Plastics Gear upon Working: Masaaki Ogawa / Yoshio Shibamiya / Minoru Iwai, 821

Title Service (1) 725, (2) 740, (3) 778, (4) 791, (5) 799, (6) 812, (7) 820